BD30 (3.0l) DI
Full mechanical injection direct injection diesel (NO glow plugs) and NO emission control garbage with a LONG stroke, great torque potential.
These engines factory will make 200hp + with just exhaust cut off and boost/fuel wound up on standard turbo. This set up has the potential to make 300 atwhp.
Bd30s are used over the 4.2 for 4x4 trials overseas, in particular Portugal for their ease of conversion and power.
These engine are incredibly rare almost impossible to find in Australia. Some are found in excavators in Australia and in the mines with imported cab-star trucks. In my opinion the best small production Diesel Nissan made.
Compatibility
Bolt straight in to qd32- NO MODS
zd30/yd25- Need terrano ti (td27ti) or qd32 gearbox/bell housing)- straight in.
or straight swap into terrano ti
swap into other navara engine variants with same gearbox change.
Will bolt directly into an d22 navaras or equivalent chassis or RD28 patrol platform with a qd32 bell housing (which is the setup used overseas, gearbox handles the abuse)
Great project for a comp truck (tuff truck) or daily driver
Entire rebuild, bottom end and top
Shimmed/cut/seated valves
New BD30 pistons Ceramic coasted crowns, valves, intake (entire combustion chamber)
Molydenderum coated skirts
Ported steel head/port matched
Fully rebuild 12mm ported/high flowed Zexel boost compensated pump with TPS
Gt3063KLV VGT with converted vacuum actuator + custom steam pipe manifold
Turbo of 4.0L Hino truck, makes 32psi before 2000rpm.
Plans were to also run twin spray water methanol injection
Engine built to run 30psi
3.0 inch dump pipe
QD32 intake manifold (best factory diesel manifold by Nissan)
Water to air intercooler (of twin turbo Toyota)
just needs heat exchanger and high flow water pump
Lightened td27 flywheel with HD excedy clutch
Arduino controller with 2-bar MAP sensor, TPS sensor and Cam/crank positon sensor for VGT turbo mapping.
NO parts missing, 90% finished ran out of funds and time.
VGT setup:
http://dmn.kuulalaakeri.org/vnt-lda/
http://forum.arduino.cc/index.php?topic=112884.0
Engine videos
https://www.youtube.com/watch?v=PTiWIoTAgsU
https://www.youtube.com/watch?v=pgqVaKMbEnM
https://www.youtube.com/watch?v=nh6gDr64hGs
https://www.youtube.com/watch?v=o6qifFFNb7w (white Tuff 4x4)
https://www.youtube.com/watch?v=9v8pmXdkLYs 12:15
https://www.youtube.com/watch?v=Cxx7UcsGKG0
Selling as I wont be able to financially fund or have the spare time for this project for at least another yr
Contact me= ph/txt= 0481337619
and pictures.
Price $6000
Full mechanical injection direct injection diesel (NO glow plugs) and NO emission control garbage with a LONG stroke, great torque potential.
These engines factory will make 200hp + with just exhaust cut off and boost/fuel wound up on standard turbo. This set up has the potential to make 300 atwhp.
Bd30s are used over the 4.2 for 4x4 trials overseas, in particular Portugal for their ease of conversion and power.
These engine are incredibly rare almost impossible to find in Australia. Some are found in excavators in Australia and in the mines with imported cab-star trucks. In my opinion the best small production Diesel Nissan made.
Compatibility
Bolt straight in to qd32- NO MODS
zd30/yd25- Need terrano ti (td27ti) or qd32 gearbox/bell housing)- straight in.
or straight swap into terrano ti
swap into other navara engine variants with same gearbox change.
Will bolt directly into an d22 navaras or equivalent chassis or RD28 patrol platform with a qd32 bell housing (which is the setup used overseas, gearbox handles the abuse)
Great project for a comp truck (tuff truck) or daily driver
Entire rebuild, bottom end and top
Shimmed/cut/seated valves
New BD30 pistons Ceramic coasted crowns, valves, intake (entire combustion chamber)
Molydenderum coated skirts
Ported steel head/port matched
Fully rebuild 12mm ported/high flowed Zexel boost compensated pump with TPS
Gt3063KLV VGT with converted vacuum actuator + custom steam pipe manifold
Turbo of 4.0L Hino truck, makes 32psi before 2000rpm.
Plans were to also run twin spray water methanol injection
Engine built to run 30psi
3.0 inch dump pipe
QD32 intake manifold (best factory diesel manifold by Nissan)
Water to air intercooler (of twin turbo Toyota)
just needs heat exchanger and high flow water pump
Lightened td27 flywheel with HD excedy clutch
Arduino controller with 2-bar MAP sensor, TPS sensor and Cam/crank positon sensor for VGT turbo mapping.
NO parts missing, 90% finished ran out of funds and time.
VGT setup:
http://dmn.kuulalaakeri.org/vnt-lda/
http://forum.arduino.cc/index.php?topic=112884.0
Engine videos
https://www.youtube.com/watch?v=PTiWIoTAgsU
https://www.youtube.com/watch?v=pgqVaKMbEnM
https://www.youtube.com/watch?v=nh6gDr64hGs
https://www.youtube.com/watch?v=o6qifFFNb7w (white Tuff 4x4)
https://www.youtube.com/watch?v=9v8pmXdkLYs 12:15
https://www.youtube.com/watch?v=Cxx7UcsGKG0
Selling as I wont be able to financially fund or have the spare time for this project for at least another yr
Contact me= ph/txt= 0481337619
and pictures.
Price $6000
