D40 Starts first time but stalls if restarted.

Scotty B · Nov 14, 2024

Hello I'm new here and trying to sort out a problem on my Dad's 2007 Navara.
On first start it will start and drive normally, although sounds a little rough, but if it is switched off and then restarted straight away it will start breifly then stall.
If it is let to sit for a minute or two it will start again and drive. I have done a lot of searching on the site and got some ideas but would really appreciate any input before I go buying parts that I may not need.
Cheers

Old.Tony · Nov 14, 2024

Overprime the fuel pump. Not by a small amount.

If the fuel system is sealed and in good condition, you'll be able to squeeze the primer bulb about 4-5 times tops before it gets quite firm (full of fuel). If this is the case, the problem may be elsewhere (see below).

If you can keep squeezing it easily, keep going until you get diesel leaking out. That's the place you have to fix. It might even be the primer bulb itself - you'll know fairly quickly if this is the case!

Other things: it's NOT the turbocharger, because the turbo isn't spinning a lot at idle.

It could be a blocked air path. Don't just check the air filter, check the entire air path to make sure nothing has gotten in to block it (birds, frogs, rats).

Suction control valve - test this by opening the fuel filler cap, start the engine, let it run for a bit, then stop and try to restart. If the problem has gone away, either the SCV is dirty (1 bottle of injector cleaner might do the trick) or it's beyond saving (scoring, pitting) and needs to be replaced. It might still be the SCV even if the fuel cap trick doesn't work.

So, a bottle of injector cleaner is good for the engine anyway, so after checking the fuel lines and the air path I'd throw a can of Liqui Moly Fuel System Treatment in the tank and drive the car.

Scotty B · Nov 14, 2024

Hello Tony, thanks very much for your help.
I'll tell you all the things I have done so far.
The truck has had a P0409 code for quite some time and I had cleared it several times in the last month or so but it kept coming back.
I got the truck off Dad two days a go to see if I can sort it out for him.
I removed the EGR and gave it a clean with some throttle body cleaner and cleared the code.
This didn't make any difference to the stalling problem and eventually the CEL came on and it was showing the P0409 code again.
Today I ran some fuel injector and fuel conditioner through the tank and I cleaned the MAF sensor with some MAF sensor cleaner and after a big drive it started very consistantly without stalling. Although I didn't realize but I had left the plug for the EGR and throttle body diconnected during this time.
I reconnected the two plugs and also replaced the fuel filter. Drove it again and restarted it a few times and it was much better but it did stall a few times. When it stalled the CEL light came on and it was showing the P0409 code again.
The truck does seem to have a lot more power after all this.
I primed the bulb and after about 5 pumps it got very firm.

Old.Tony · Nov 15, 2024

The fuel system seems ok, then!

The error code usually means the EGR valve is in dire need of attention. You can try just spray cleaning it but taking a look in the electrical connections might reveal some oxidisation in there (it's been reported before). Let me find a post by someone who's done a rebuild on one of these for you ... here it is!

https://www.nissan-navara.net/posts/674386/

Scotty B · Nov 15, 2024

Thanks very much for your help Tony

Scotty B · Nov 15, 2024

I followed all the steps in that post. My EGR was fairly clean under the cap. I removed everything and even tested the little motor. Everything is moving freely with no binding. I don't think I left anything out but unfortunately after about 20 minutes of driving and then restarting the truck it threw the code again.

Old.Tony · Nov 16, 2024

That's a little disappointing, the 2007 EGR system is not very intrusive and most failures are basic ones unless the entire gizmo has failed.

Any chance of grabbing an EGR valve off a nearby wrecker? Most cars aren't written off due to a failed EGR!

Scotty B · Nov 17, 2024

Thanks again Tony. I'll contact some wreckers next week. It also needs a clock spring. I already purchased one and got the Cruise Control and Horn working again but I just can't get the light on the dash to stop flashing. I have tried the key on key off sequences so many times but it still stays on. I did get it to flash in a code sequence though which is one long and two short. The truck has only done 170000 klms and been pretty well looked after but it does have these couple of issues.

Old.Tony · Nov 17, 2024

If it's the airbag light on your dash that won't go out, mine did that for the clock spring but also did it when my airbag diagnostic module went on the blink. I've replaced that unit twice now, the last unit has survived quite well. You'll need a T50 Torx security bit to remove it.

Scotty B · Nov 25, 2024

Hello Tony thanks for all your help. I got a new EGR valve and solved the CEL light problem. Also got another Clock Spring and that light has gone now too. Seems that it is going very well now. I really appreciate all your advice. Cheers

D40 Starts first time but stalls if restarted.

Help Support Nissan Navara Forum:

Scotty B

Member

Old.Tony

Administrator

Scotty B

Member

Old.Tony

Administrator

Scotty B

Member

Scotty B

Member

Old.Tony

Administrator

Scotty B

Member

Old.Tony

Administrator

Scotty B

Member

Similar threads

Latest posts

D40 Starts first time but stalls if restarted.

Help Support Nissan Navara Forum:

Member

Administrator

Member

Administrator

Member

Member

Administrator

Member

Administrator

Member

Similar threads

Join the conversation!

Join today and get all the highlights of this community direct to your inbox. It's FREE!